I need to repaint some wheels in Opal Pearlescent Paint. Does anyone have a color code for it. I believe the Performance Red mentioned is EY. I have a 92-1/2...
I have a 1989 LX 5 liter that I am getting a engine code for the TPS. In my Hayes manual it says not to try and change the TPS because it needs to be tuned...
I did the research and the last year for a barometric pressure sensor (aka map sensor not hooked to the manifold) was 1993. the 1994 and 1995 5.0's did not use...
I general terms a TPS Trottle Position Sensor is a reostat or variable resistor. Resistor with three wires, one wire is a wiper. Basically with a DMM or...
Maybe true. The 93 + computers had alot of changes in them and I'm not as familiar with them. KC ... From: Keith To: 302mustang@yahoogroups.com Sent: Monday,...
I installed the 5.0 MAF sensor tonight and it runs great now. Maybe more power than it had with the 86 computer. Now I just need to adjust the TPS and tune it...
Thanks for the information. If I replace the old TPS are there settings I need to know or do I have to get readings from the old TPS and try to match the new...
Just for the hell of it I have spent like 2 hours going through the 5 sets of Ford shop manuals I have here for this information. I found out that Fords back...
I just re-wired my mustang and the website I used was extremely helpful, especially when it came to testing/adjusting the sensors. Got to fordfuelinjection.com...
If your certain the TPS is bad, just bolting in the new TPS should do the trick. There should be no need to adjust the TPS. Years ago a lot of people made i...
Badly in need of a steering colum for my baby (an 83 GT). Was broken when I got the car, gotten progressively worse, and just about ready to leave me not able...
I have a 92 steering column available. From: 302mustang@yahoogroups.com [mailto:302mustang@yahoogroups.com] On Behalf Of Shannah Sent: Thursday, July 31, 2008...
I was just looking for some other shop manual I have and found the Ford truck Electrical & Vacuum Troubleshooting manual. Looked in it and nothing about TPS...
Hey guys I heard of this site before but I found this out on myspace the site www.autoperformanceempire.com/autocommunity is having a contest and the first...
Thankx but from what I understand it has to be same year for some reason. I'm still looking into what the deal is with that...and if I can work my way around...
What is the issue your having? I know the shift mechanism is a weak point, where it breaks and you cannot shift out of park. The key can cause problems,...
Found this link of auto wreckers http://www.automotix.net/partshotline-ford-mustang-mechanical- requests.html go down the list. Many higher end auto wreckers...
I am pretty sure all the steering columns were the same 1980-1984, other than cosmetics. All those should bolt in and have the same coupler for the rack at the...
Was told that, as far as the steering colum, 83 was an isolate year and could only be replaced with an 83. Got the car from my idiot brother-in-law - who...
I find that the U-Pull type junkyards have a lot of older cars. The full serv junkyards only have newer cars. The bad news is the u-pulls can not tell you...
Yeah - haven't seen too many of these cars in the upull it yards...especially when it comes to my specific year...and around here most yards tend to pull...
We hope you can make some of these events: SCMC/Parkway Ford's Mustang & Ford Show - Winston-Salem, NC - August 23, 2008 Join the SCMC on August 23rd in...
I am going to be converting my 93 2.3L auto to a 2.3L 5spd. I know the 2.3L 5sp is different in the input shaft size and gearing from the 5.0 5Spd but, is...
Hi everybody. I have basically stock 302 86 5.0 GT. I do have under drive pullies, MAC cold air intake, SMOG delete, MAC shorty headers. Can I bolt up my new...
Did you buy the matching EGR spacer? 70mm T-body is a bit of an over kill for a stock intake. You should have no problem bolting it up, and its a great idea if...
I agree. You can put a 90mm T/B on it and the motor will only flow as much as it can with the stock parts. Back in the day, I used to gasket match the stock...
