Hi there , is there anyone in Australia that knows where I could find a complete cab {doors and all } for a 1936 Fargo 1.5 ton truck A T.J.R {Richards S.A...
hey does anyone remember where the washers go to bring the hood back down, when it has been blown open making the back end set high? The hinges look fine. ...
To bring the back of the hood down, need to shim the front leg of the hinge at the hood, if the metal is to far stressed it may not help too much...
jeffc
jeffc@...
Apr 17, 2004 8:52 pm
3710
Thanks for the reply Jeff. I did that yesterday and it brought it up more. I did it at the hood. I guess I will try something else. Thanks again for the reply....
You could always try the rear leg and see if that will help, sounds odd, but it may do the trick...
jeffc
jeffc@...
Apr 17, 2004 11:59 pm
3712
I came across a Dodge Truck Parts catalog 1960 and O own a 61, but I think I can use some of the info in it. It has light duty, medium and heavy duty truck...
A: The hinge on the fender needs to be loosened and tipped forward to drop the hood down. From: "Steve Emery" <steveng@...> Subject: 61 D-100 hey does...
Jim, no hinges on fender, only hood and firewall. I took the hood off today. I don't own a welder, but need to have medal welded over the holes where the bolts...
Heck, if you were in the Portland, Or. area and could use a one for a 67 I'd sell you a good hood for that price, shipping would make it prohibitive. The...
jeffc
jeffc@...
Apr 19, 2004 5:09 am
3716
A: Doh! Sorry, I meant loosen the firewall bolts and slide the hinge down. I put a plate of steel behind the firewall of mine because it did the same thing (a...
I'm not getting that welder, but I do want one and will look for a Lincoln welder down the road. I have a ton of tools, but never owned a welder? I just used...
Have any of you been reading about the new Chrysler 300 Hemi? It switches from a V-8 to a 4 Cylinder. The good news is that they are coming out with other...
Howdy all, I just wanted to pass the word along about the new Spinflow oil filter made by NAPA. I just bought one for myself recently and I honestly couldnt be...
I own a 1981 dodge ram with a slant six, bought it used and the person who own it before me put on it a 4-barrel, an electric fuel pump, and headers. I changed...
A: When you hooked up the fuel line to the Carter BBD carb, you may have crunched the brass fitting. It is the seat for the needle and seat. Nice part is you...
Hey Bill, I have an old 1961 Dodge D-100 that I thought I had the same problem with. When I wash it, water ran down from behind the dash onto the floor. I...
... problem with. When I wash it, water ran down from behind the dash onto the floor. I thought the fresh air vent was causing it, but after looking it was a...
Low miles, original condition Fire Chief's Van from New Chicago Fire Bepartment in Hobart, Indiana. Go to www.littlesturgeonwi.com and then to the About Page...
Greetings all, We are having to fix or replace the carb in our Camper Special. The original is a Carter, the one in it now is a Holley, we have to decide...
Go to Hemmings Motor News. Look in the classified. I have a 68 Buick Riv. The carb was past rebuilding. In Hemmings classified...I found a brand new, never...
A: Redo the Carter. It's far easier to work on. Then get one of those @$10 see through inline filters and put it before the fuel pump where you can get at it...
Great idea, thanks, we had sort of forgotten about Hemmings. Did scout around on eBay a little but probably ought to look a little more. Thanks for your...
Thanks, that was Bob's initial instinct, to focus on the Carter, but thought we should seek other opinions in case there was something we didn't know about the...
