The Laboratory Robotics Interest Group Discussion Group is for comments or questions about Laboratory Robotics and Automation. You receive messages posted to...
lrig-discussion@yahoo...
Mar 1, 2008 8:54 am
5970
Hello, I am looking into designing an e-notebook system, and would like to know if there are any standardized requirements or regulatory guidelines govering...
Hmmm, I'm no expert but you could do yourself no harm by taking a look at the regulations for CFR21 part11 from the US FDA. Cheers, Neil ... -- -- Neil Benn...
Neil Benn
neil.benn@...
Mar 21, 2008 11:47 pm
5973
Check out www.censa.org <http://www.censa.org/> They have done a lot of work establishing guidelines for ELN. I suspect you have to pay for their information...
When you've cracked this one I would be really interested to have a short article from you for the next issue of my ezine. David ... [Non-text portions of this...
Dear Fellow LRIGers, At the upcoming SBS conference in St. Louis, there will be a Special Interest Group meeting on Automation Quality Control. I think the ...
John Bradshaw
JBradshaw@...
Mar 28, 2008 5:31 am
5976
Hello, I am doing a bit of research on I am trying to track down a -20 degree cabinet sort of based upon the same principal as a product/operator protection...
Neil Benn
neil.benn@...
Apr 1, 2008 4:00 am
5977
All, Sorry about the formatting of the previous message. Let me try again. Here is the agenda (hopefully with more understandable formatting) for the meeting:...
John Bradshaw
JBradshaw@...
Apr 1, 2008 4:00 am
5978
The Laboratory Robotics Interest Group Discussion Group is for comments or questions about Laboratory Robotics and Automation. You receive messages posted to...
lrig-discussion@yahoo...
Apr 1, 2008 8:04 am
5979
Hi, Can anybody help me with a list of RS-232 commands for the Cytomat 2? There must be one of you who actually wrote their own interface for it, right? Best...
Hi Jacob! We wrote it, what is your problem? Best regards, Attila ________________________________ From: lrig-discussion@yahoogroups.com ...
Bielik Attila
a.bielik@...
Apr 3, 2008 4:49 am
5981
Hello, I'm doing a bit of research (may make a JALA submission out of it if you would like to join in), in addition to automation - I have done (and mainly do...
Neil Benn
neil.benn@...
Apr 3, 2008 4:49 am
5982
Hi Jacob try to contact Stefan Czwak Technical Specialist Cytomat / Incubators at Kendro Tel.: +49 (6184) 90-6367 Fax: +49 (6184) 90-7367 E-Mail:...
You've raised a interesting issue, one that has in part contributed to the work I'm currently doing. The places where open source software exists, and why it...
LRIG members, I have a BioMek FX with a single 96 channel pod. There has been a persistent problem using the grippers in the most forward plate nests. It has...
GRAY (James Gray)
grayj@...
Apr 11, 2008 3:45 am
5985
Hi, Does any of you have a experience comparing fluo and luminescence cameras in both machines? Is the new ICCD camera on Tetra+ just as sensitive for...
Hi all, My first posting to this group, although I'm a member of ELRIG. Anyway, I'm looking for information on the serial communications protocol and command...
Hi, I had similar problems with earlier FX all the time - in my cases, the air tubings actually came off, so it was very obvious it was getting caught...
Hi, I experienced this problem a number of times on different FX's Most of the time it occurred it was due to the pneumatic air hose getting kinked when the...
Hi Robin, Are you trying to integrate a Twister I or Twister II? And are you planning to make calls through RS232 commands using MSCOMM or through the API of...
Dear All, I am looking into available automation of probe preparation for microarrays. We work with Affymetrix resequencing arrays but set-up methods will be...
Agnieszka, There are more liquid handling workstations available for you to choose from. Join the Simbiotix community and search for liquid handler or...
The last time I spoke to Affy they were about to automate their service lab. It might be worth getting your rep to put you in touch with the lab manager. Affy...
For low-throughput microarray preparation, you could consider BioTX Automations WellAware pipetting systems. They recently added electronic protocol...
Dear, I used a FDSS 6000 reader for several years. You can contact me off line for discussion if this can help you. My email address:...
Thierry Christophe
thierry.christophe@...
Apr 22, 2008 2:59 am
5996
Hi Neil We can probably offer you something through our distributorship of the KEMS systems. If you are interested please contact me off-line and let me have...
David Ley
david.ley@...
Apr 22, 2008 3:00 am
5997
Hi Neil I've been working with the LabView programming language for many years now. One of its many advantages is that there are several lively open source ...
Hi Kai, I'm looking to use MSCOMM to control the Twister. It's a Twister I and I have no documentation at all for the control codes for it. I presume it has a...
