Royal Enfield Mailing List - a note from the moderator "Guidelines for Use"... sent automatically on joining, and each month thereafter. Updated occasionally. ...
royalenfield@yahoogro...
Feb 1, 2006 12:35 pm
44235
Hey John, Its possable...... Oh yes its possable...... to inadverntly put in the gears the wrong way....I know c'aus i've done it a time or 2...if you want...
You could advertise it in just about any newspaper's classified ad section, either in the special notices section or the motorcycle section. There's some guy...
As far as License Plate Collectors, there are several that advertise looking for plates in "The Antique Motorcyle" magazine. Contact me off list and I'll...
What are the differences b/w the Avon Venoms and the Dunlop K81's? Also, is there anything out there that's a bit wider and would fit the Bullet? Thanks.......
I have recently fitted an in-line oil filter into the return oil feed. A 1/4" pipe from the engine, to the filter (Kralinator L-77, FRAM PH2839) mounted where...
Totally different frame on the later (post 57?) Reddiitch Bullets..It is 'missing' the 'saddle post' that runs down to the top of the gear- box. (Much better...
... much oil cooled as air cooled. The cooler the oil over the head, the more heat it can carry away with it. Most motors and oils exhibit optimum durability...
Ok Hi all from downunder I have a 46 AJS 500 single rigid frame and a 53 AJS 350 single Jampot frame and a Bullet 65. Where to begin .....the Bullet is a 5...
I can attest to the fact that the Twin Port head will not give a performance enhancement.(As was noted when we sold the few I had made) My experience with...
... something like this? http://img453.imageshack.us/my.php?image=oilfilter1yl.jpg works nice, and the and the oil keeps clear, so it shouldnt hurt the engine ...
Similar. I have mounted my filter away from the exhaust header pipe so that it is not as likely to pick up any heat from the pipe, or get hit by rocks flicked...
Definitely suspect... At the very least the entire front end has been replaced with Indian made parts. You may even want to check to see if it has been...
I have been reading through the archives, and came across this message on cams that I felt compelled to reply to: Cam timing checking specs often include large...
Hi Simon, Thanx for the report.......after I get some miles on the 53 AJS 500 I will try to give a report of my impressions. Regards. Clay ... Jampot frame ......
Are the torque values in the manual dry, or with never seize or some such lubricating material on the threads? _______________________________________________ ...
Couldn't agree more, plenty of oil, and the cooler, the better. In fact, I'm in the middle of fabbing a bracket to mount a filter to the front motor mount. I...
... i went to work today on the enfield, starting it at minus 4 degrees C was not too much of a problem but the kickstarter took several seconds to come back...
All of the ultra cool street rodders lag their headers so that they stay hot. Hot headers keep ex. gasses moving at higher velocity, the sonic reflections are...
The temp of the Outside of the oil filter, and the temp of the oil in the sump will be two completely different things. I too can comfortably hold onto my...
... Tim- N.Z. BUT..... Tim- I've got about 1/8 inch gap seperating my ring from the head... that makes it just a heat sink that does not transfer heat to...
Isn't that the supply line? Doesn't oil get pumped up the line and then through some holes to the top of the rocker arms? Take the pushrod cover off and...
further to my prev. missive the vendor has given me an engine number of G 2555 22. Does anyone recognise it at all ? BTW he now says the bike is a 1965. ...
Net-motorcycles.com: two million words on new and used bikes, 1000s of riders' reports... at http://www.umgweb.com New Bike News ... Bits and Bobs Bikebandit...
