The dielectric grease suggestion for protecting electrical contacts is a good one; however, it might not be corrosion at all that is the source of your ...
So far as I know we do not get Ethanol in our petrol yet as normal .A few garages can supply E85 which has 15% ethanol in it but I believe plans are in the...
Does anyone monitoring this list have access to any of the engineering drawings from RE? I would really like to know all the variations of the crankshaft drive...
Royal Enfield Mailing List - a note from the moderator "Guidelines for Use"... sent automatically on joining, and each month thereafter. Updated occasionally. ...
royalenfield@yahoogro...
Nov 1, 2007 11:36 am
56851
... So then .. celebrity gossip is still fair game. -d...
What about sex and good looking babes they do not seem prohibited. So who is the best looking babe on Television in the UK in a regular slot no film stars on...
CJay, While welding for a local company there were many times that I had to do extra welding because a part was made incorrectly by the machinist and we fixed...
Ok, it was a bad joke. I'm really really sorry I said anything. Really. We don't know anything about UK television babes, Robbie, but suspect that your ...
No it is not insulting the character that plays Rosie Webster in Coronation street is now in the soap supposed to be 16 but she is played by a 19 year old well...
What is the purpose of the groove that runs down the detent plunger pin? Is it supposed to key into something or does it just allow for the passage of...
CJay, I had exactly the same problem with the crank/rod assy I bought from CMW. Splined nearside output shaft about .020" too big. I wasn't going to strip the...
... The groove is to keep it from spinning around. Spin it around untill the blade of the plunger is lined up with the slot in the end of the screw and peen...
... Thanks for the reply. I suspected that was what the groove was for, so I did "peen" the outer housing into the groove. However, this prohibited me from...
I have just verified that the Hitchcock's billet crank for kickstart engine fits the spline of the Bob Newby belt drive pulley perfectly like a glove. No...
Has anybody tried this?? Sounds like it could even help a well broke in unit. I thought my 5 year old Bullet shifted ok but this makes a lot of sense. - Mike ...
... I did it to my 95 and it made a world of difference. When I did it to the 99 the factory had already caught on and lightened the spring to one lighter than...
Hi Mike, I found this link which seems to be the flatslide carb from CMW. http://piled-arms.com/jrccarb.html Click on the link to pictures to see but it looks...
... Dave, You took off .020 with emery paper? Wow, you must have the patience of a prison inmate that's in for life! Anyhow, thanks for that info. I intend to...
Is it possible to remove the inner gearbox cover without removing the ratchet mechanism? Would I need a puller or other special tool to remove the inner...
In my ongoing effort to determine if there are two or more different drive shaft sprocket spline demensions on post 2000 bullets I am asking for some help. If...
CJay, I have just measured my belt drive wheel which fits on the crankshaft. This unit is a perfect fit on the Hitchcock's crank splines. The Hitchcock crank I...
... Snap connectors are there for assembly line expediency. They do no good at all for the user, and can leave you stranded while you figure out where the bad...
... Thanks Ace, The .020 or so difference in the large diameter jives with what I remember. I guess my doubts lie in the fact that they were advertising the ...
... I got some from the shaft, using medium emery, oil, and the old "shoeshine boy" motion, but also took out the inside of the sprocket with a drum sander on...
Ace- the output shafts ARE different for ks. Most notably the machining for the es. makes sense that the splines could not be the same as most peeps would not ...
... (the ... CJay, My engine cases are 2002 4-sp kickstart metric cases. I ordered the crank for that, but I was told that it would fit any kickstart-only...
Sounds as if your plunger housing is split. I think when you order a new one, you'll see what I mean. Part No. 11094 I think. (The whole assembly) ... Not to...
