If you delete this ... you seriously don't have a heart. This story is 100% true, Forward in Sep. Please one people forward 10 e-mail the world and send one...
Hey guys, I have a question. My Mustang is a '68, with the C code 289. It's got 76K original on it. Where is the oil pressure guages needle supposed to lie?...
... Lee, The gauge sounds about right in both cases..............Dennis Donovan...
Dennis Donovan
riker@...
Sep 4, 2003 4:49 pm
1368
Hello All, I just joined this group because I am looking for information on classic Mustangs. I am in the shopping mode looking for my first one. I am looking...
Hi Group, My stepson Jason and I are new to the list. He just spent his hard-earned money, and bought his first car. It's a 66 Mustang coupe with a 289...
We received both of your messages. Welcome to the list. There is an extreme amount of information available to you, both through this group, as well as other...
John, As far as the '71 to '73 Mustangs go, look for rust around the rear wheel-wells. Also, inspect the floor pans, both from the top, as well as the bottom,...
Hellooooo, is anyone out there? Jason thanks for the welcome. I am trying to determine who makes the best reproduction sheetmetal for vintage Mustangs? Thanks,...
Thanks for the information Jason. I am hoping to go look at the car wednesday or thursday of this week. As far as looking to see if the numbers match, where...
The numbers should be near the back of the block, just above the starter. I am not too sure if they are visible with the starter in place; they may be. I ...
Getting ready to install new alternator on 72 351c fastback (w/ ammeter)...hooking up the BAT cable is a no brainer...but how can you identify the stator and...
The terminals should be stamped on the back of the alternator.If you need I have Ford factory wiring diagrams for 71 & 72 mustang. Dave ... From: josie wales...
All, I am looking for a '69 -'72 MACH1 project car. Something with a decent body, and running, but in need of Tuning, TLC and finishing. I am in PA but looking...
In michigan. But i travel to ky on a reg basis ... __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design...
I need advice about restoring a 1965 A code GT coupe. The car has spent it's life in the mid-west and has suffered some serious rust damage. About 12 years ago...
You don't have to be a millionaire!Free registration! This is the best place in the world where you can meet successful, beautiful singles for a date, fun,...
Paul, Here is my own personal opinion on the matter. No average Mustang, even if it's a GT, is worth spending upwards of $20k on a restoration, unless it's a ...
Jonathan Thanks for your response. The thoughts you expressed match thoughs of the other Mustang enthusiasts who have answered my post. Once I do make my final...
Paul, How bad is the body work required? Structural or Cosmetic? Give it a quickie at Maaco, then drop in the 302 and drive and enjoy it. I see many daily...
AMEN! Jonathan Harbour <jsharbour@...> wrote:Paul, Here is my own personal opinion on the matter. No average Mustang, even if it's a GT, is worth spending...
I have the opp to buy a 64 coupe, 6 cylinder, daginham 4 speed. Everything there, all original except for tires, etc, and had been repainted, not great/not...
Well, Tomorrow I go pick up my '72 Grande. I found it on Collector car trader online. It has had a lot of work done to it already, so it is in pretty good...
I got a new alternator wiring harness from the Paddock...The connections at the alternator match, FLD, GRD, & BAT I believe is the way they should go... On the...
If you delete this ... you seriously don't have a heart. 100% true story, Forward in Oct. Attacks the Hong Kong terrorist needs the world people's power. My...
